Page 1 of 1 1
Topic Options
#1058108 - 08/06/11 09:38 AM VM 3100 Pro - how to enable RMDB outputs
Jury Offline
Space Cadet


Registered: 08/06/11
Posts: 1
Hi all,

I need to setup multi-channel recording from Roland VM 3100 Pro mixer with RMDB cable + RPC-1 card. I've reset its settings, but still on the TRK output screen I see zero levels and nothing comes to PC.

Is there something special to setup to make RMDB output alive ?

Thanks,
Jury.

Top
#1420010 - 09/24/15 12:58 PM Re: VM 3100 Pro - how to enable RMDB outputs [Re: Jury]
alds Offline
Space Cadet


Registered: 12/08/09
Posts: 6
Loc: Mexico City
This is from Roland Page

REGARDLESS OF SOFTWARE USED...set up the VM-3100Pro to work with the RPC-1 card and various recording software by using the following steps:

1. Reinitialize mixer to factory defaults, as per page 57 of the VM-3100Pro Owners Manual. *******Not necesary********

2. Press [SHIFT] & [F1] to "LOAD LOGIC CONFIG", then press ENTER/YES.

3. Press AUDIO CH button until it is green, then pull faders 13 though 20 (1 through 8) down, then back up to 0 dB.

4. Press channel 13 SELECT button, and set PAN full left using V1 knob.

5. Press channel 14 SELECT button, and set PAN full right using V1 knob.

6. Press AUDIO CH button until red, then press LEVEL/METER to set parameters.

7. Route the inputs and outputs appropriately in the DAW software that's being used. Check the software's documentation and/or online help for proper setup instructions with an audio interface (such as the RPC-1 card that the VM-3100 is connected to).

8. IMPORTANT NOTE: If the Logic preset steps above (step 2) do not function properly, start over with step #1 and then use one of the following (however, the Logic preset above is still recommended to try first regardless of the software being used)

Cakewalk - SHIFT + F2
Cubase - SHIFT + F3

NOTE: The [SHIFT] & [F1] ("LOAD LOGIC CONFIG") template is the only one that configures the mixer to route control and audio to and from the RBUS port, and should be used in conjunction with the RPC-1 card and various compatible software packages.


I have always use it with shift + F3 for cubase and use in cubase and works perfectly

Regards
Armando

Top
Page 1 of 1 1


Hop to:
Shout Box

Who's Online
2 registered (Logrinn, jimmyrock) and 12 anonymous users online.
Top Posters
51932
Jazzooo
43828
Al
40001
Silversmith
39122
Timster
32942
Tom Mix
29502
Ismellelephant
28844
Popmann
28768
NOK
28627
gonzo
28324
Mooseboy
26648
moontan
26476
Doughboy
26071
C Jo Go
25141
flatcat
23691
paulb
23317
Marty Gilman
23279
RGR
21692
fabulousthunderbird
21125
fonts
20593
Gretsch 6120
19598
vvvm
19427
String Jammer
19315
glensimonds
19173
Vanillagrits
18923
T57Strat
18894
GAMBLE
18791
Jammer
18069
SteveW
17931
JazAddict
17600
GAWZDigitalUnderground
17522
Geo
17280
Hano
16175
Delso
16058
Liquidirt
16053
Dave Morris
15821
LakeStone Karl
15629
slotz
15386
Milkman
15342
Dan Barnes
Forum Stats
21034 Members
29 Forums
139891 Topics
1610500 Posts

Max Online: 290 @ 11/19/19 07:32 PM
Newest Members
Logrinn, 0861, Predrag, Roode_Poon, JR97
21034 Registered Users

Generated in 0.034 seconds in which 0.027 seconds were spent on a total of 13 queries. Zlib compression disabled.